With everyone getting “green”, the next generation light bulb source is the LED. This stands for light emitting diode, and they are designed to last over 50,000 hours and:
- Consumes 85% less energy than incandescent
- Consumes 50% less energy than fluorescent
- No mercury (fluorescent)
- Fewer greenhouse gas emissions
- Less landfill waste from burned out bulbs of all types
A Light Emitting Diode (LED) is a semiconductor device which converts electricity into light. LED lighting has been around since the 1960s, but is just now beginning to appear in the residential market for space lighting. At first white LEDs were only possible by "rainbow" groups of three LEDs -- red, green, and blue -- by controlling the current to each to yield an overall white light. This changed in 1993 when Nichia created a blue indium gallium chip with a phosphor coating that is used to create the wave shift necessary to emit white light from a single diode. This process is much less expensive for the amount of light generated.
Each diode is about 1/4 inch in diameter and uses about ten milliamps to operate at about a tenth of a watt. LEDs are small in size, but can be grouped together for higher intensity applications. LED fixtures require a driver which is analogous to the ballast in fluorescent fixtures. The drivers are typically built into the fixture (like fluorescent ballasts) or they are a plug transformer for portable (plug-in) fixtures. The plug-in transformers allow the fixture to run on standard 120 volt alternating current (AC), with a modest (about 15 to 20 percent) power loss.
The efficacy of a typical residential application LED is approximately 20 lumens per watt (LPW), though efficacies of up to 100 LPW have been created in laboratory settings. Incandescent bulbs have an efficacy of about 15 LPW and ENERGY STAR® qualified compact fluorescents are about 60 LPW, depending on the wattage and lamp type. Some manufacturers claim efficacies much higher than 20 LPW; make sure to examine system efficacy, which accounts for the power use of all components. In December 2006, the U.S. Department of Energy studied the efficacy of four luminaries. All four fell short of the manufacturers' claims; the study implies that manufacturers are relying on measurements of how much light an isolated LED produces, rather than how much light an LED luminaire actually delivers.
LEDs are better at placing light in a single direction than incandescent or fluorescent bulbs. Because of their directional output, they have unique design features that can be exploited by clever designs. LED strip lights can be installed under counters, in hallways, and in staircases; concentrated arrays can be used for room lighting. Waterproof, outdoor fixtures are also available. Some manufacturers consider applications such as gardens, walkways, and decorative fixtures outside garage doors to be the most cost-efficient.
LED lights are more rugged and damage-resistant than compact fluorescents and incandescent bulbs. LED lights don't flicker. They are very heat sensitive; excessive heat or inappropriate applications dramatically reduce both light output and lifetime. Uses include:
- Task and reading lamps
- Linear strip lighting (under kitchen cabinets)
- Recessed lighting/ceiling cans
- Porch/outdoor/landscaping lighting
- Art lighting
- Night lights
- Stair and walkway lighting
- Pendants and overhead
- Retrofit bulbs for lamps" Task and reading lamps
Definitions and Terms
| Term | Definition | Units | How to interpret |
|---|---|---|---|
| Color Temperature | Color of light | Kelvin (K) |
|
| Color Rendering Index (CRI) | Light's effect on color | Scale of 0 to 100 with sunlight at 100 | The higher the number, the more "true" the color will look in that light |
| Brightness | The intensity of the light. | Lumens | The higher the lumens, the brighter the light |
| Power | Amount of electrical energy consumed | Watts | The lower the watts, the lower the energy consumed |
| Efficacy | The efficiency of the bulb to convert electricity into light | Lumens per Watt | More efficient bulbs provide more light using less energy |
Ease of Implementation
No additional tools or training are required for installation of LED fixtures.
Initial Cost
The biggest limitation to LED for common residential use is the cost of manufacturing due to still-limited production runs. Manufacturers claim production will increase considerably in the near future, further lowering prices. Currently, there is a limited number of LED fixture manufactures, but this is changing. Retrofit bulbs range from $25 to $60 for night lights and small lamps.
Operational Cost
The cost savings of LEDs can be found in smaller wattage lamps or for applications that take advantage of their longevity, such as difficult to reach places. They are also advantageous for dimmable fixtures, since dimmable fluorescents are expensive.
U.S.Code Acceptance
As with any electrical device, LED fixtures must be listed for use such as with a testing laboratory label. LEDs are not specifically referenced in building codes.
Installation
The small size of LED lights encourages a variety of design options. White LED lamps are available with Edison (screw-in type) bases to retrofit existing fixtures. There are LED strips that can be used under cabinets. In addition, outdoor landscaping fixtures are available.
Warranty
Warranties for LEDs can range from 3 to 5 years, depending on the manufacturer.
Benefits/Costs
LED lamps have many advantages over traditional lighting methods. These include:
- Low energy consumption - retrofit bulbs range from 0.83 to 7.3 Watts
- Long service life - LED bulbs can last up to 50,000 hours
- Durable - LED bulbs are resistant to thermal and vibrational shocks and turn on instantly from -40C° to 185C°, making them ideal for applications subject to frequent on-off cycling, such as garages and basements
- Directional distribution of light - good for interior task lighting
- No infrared or ultraviolet radiation - excellent for outdoor use because UV light attracts bugs
- Safety and environmentally conscious - LEDs contain no mercury and remain cool to the touch
- Fully dimmable - LEDs do not change their color tint when dimmed unlike incandescent lamps that turn yellow
- No frequency interference - no ballast to interfere with radio and television signals
- Range of color - LEDs can be manufactured produce all colors of the spectrum without filters, they can also product white light in a variety of color temperatures
There are some current disadvantages to LED lighting:
- LEDs are currently more expensive than more conventional lighting technologies, and may be hard to locate
- LED are very heat sensitive. Excessive heat or inappropriate applications dramatically reduces both light output and lifespan
- LEDs typically cast light in one direction at a narrow angle compared to incandescent or fluorescent lamps so lenses or reflectors are needed in fixtures to broaden the beam (if desired)
Disclaimer:The information on the system, product or material presented herein is provided for informational purposes only. The technical descriptions, details, requirements, and limitations expressed do not constitute an endorsement, approval, or acceptance of the subject matter by the U.S. Department of Housing and Urban Development (HUD/FHA), The Partnership for Advancing Technology in Housing (PATH), or any PATH-affiliated Federal agency or private company. There are no warranties, either expressed or implied, regarding the accuracy or completeness of this information.
